#FSUIPC 4.80 DOWNLOAD PRO#

I am going to Connect the CH Pro pedals to the TQS after rewiring them totally to Work in Plane Mode Only since I also have an old TM Racing Set I can convert if needed. Switch (small white button) but you could if replacing the Eraserhead with a small PS2/3 Joystick button or similar perhaps. On the TQS the Thumb Eraser Button (mouse emulation) must be replaced along with it's wiring, I plan to use an extra FLCS Hat Switch since I have some in a Repair Kit I bought many years ago from TM and it seems to fit kinda Ok in the hole left by the Eraser Button box which can be removed in one piece easily.

The Wiring and PCB inside the FLCS Handle is KEPT, the PCB already has 4021 Shift Registers for the Buttons etc to reduce the number of Wires needed and so it can be reused as is by connecting 4 Wires to the ICSP Header and the red to an AI pin on the Arduino. On the Hardware front Sokol1 has pointed out that both the FLCS and TQS PCB Boards get totally removed from the Bases and are not reused at all in the Conversion along with a lot of the Wiring in the Bases needing Changing or replacing, this makes room for the Leonardo Boards that will take over all the old PCB Functions so it does not matter if you have the Original FLCS Chips (v3.04/3.08) or the Stickworks Digital Chip Upgrades that came out in about 2000 as the Original PCB is not used at all.

#FSUIPC 4.80 DOWNLOAD CODE#

My extra Kuman Leonardo Clone Boards arrived from China (only one week excellent time) and I did not load the Arduino Blink sketch as I did on the Original Leonardo ( per Arduino instructions) and both boards instantly showed me the Bootloader Com Port after hitting the Reset Button the 1st time, and I loaded MMJoy2- with no issues unlike the 1st time and then programmed two axis and changed the USB VID and PID and name on each one so windows sees them differently, again with no problems unlike the Original Board, so I think the Trick is NOT to load any other Code to New Leonardo Boards before you Upload the MMJoy2 Firmware ,as it seems to cause issues with the USB Port as it is being constantly Polled by the Blink Sketch that is already in the Firmware causing an issue for MMJOY2, the Arduino 1.6.3 IDE, does not have any issue finding the Bootloader Port itself BTW, it scans for the Bootloader Port and then uploads, MMJoy2 does not do this.

#FSUIPC 4.80 DOWNLOAD DOWNLOAD#

But reading about the GND and RESET Pin on the Arduino Pro-Micro and touching it's GND and RESET Pins twice quickly to do it, gave me the idea to quickly push the Leonardo Reset button quickly twice and it worked ! and gives me 5-8 secs to hit the Firmware download button in MMJoy2 now.

It would disappear (per the MMJoy2 Wiki) but almost instantly reappear on the same Com Port. The Leonardo I already have, I had issues with it's Reset Button not initiating the Boot Loader Mode, this maybe because when I got it I loaded the Blink Sketch from the Arduino IDE (1.6.3) per the Arduino Website Leonardo Setup Tutorial, and thus the Computer is constantly polling the Leo running the Sketch and apparently did not 'see' the Reset Command, so the Reset button would not 'reset' the Leonardo to bootloader mode.

I am planning on using a Clone Leonardo Board ($12-15 each) in both the TQS Base and the F16-FLCS Base to help simplify this for myself as I don't do electronics as a hobby or otherwise, though I have plenty of experience with Tools and Soldering, and have bought myself a Hakko FX-888D and a couple of Tips for it and have to say it is a nice quality Tool which I appreciate, but it isn't really needed though Temperature Control and fast heat up is nice after years of a standard 25w Stick Soldering Iron ( now with a bad tip ) I have been gathering Info and Pics from Numerous places to start this Process, so I'll add that Info in posts below and try and add Ideas and Pics of my own as I go, but any ideas or suggestions will be greatly appreciated. page is in Russian but I don't think you need to translate to see Dates uild-your-own-usb-controller#Post4322189ДЇIRMWARE DOWNLOADS PAGE. The MMJoy2 Main Thread with Links to MMJoy2 Firmware etc is over Here:

I am planning to Convert my gameport F16-FLCS + TQS (Original) to USB along with my CH Pro Pedals after reading the MMJoy2 Thread and posting a few questions there but thought I should start another thread here, so as not to clutter up that thread, so I will copy some of that info over here too but 1st many thanks to Mega_Mozg_13 and Sokol1 to start.

Fsuipc 4.80 download